In printed circuit board (PCB) and flexible printed circuit (FPC) manufacturing, inks are more than just a cosmetic layer. They protect copper traces from oxidation, provide electrical insulation, and help define the functionality of the finished board. Whether it's solder mask, legend ink, or conductive ink, each type has specific properties that influence printability and long-term reliability. This article reviews the key characteristics of inks, their roles in the process, and practical guidelines for storage and use.
Roles of inks in PCB and FPC production
Ink serves a protective function during fabrication, covering copper foil so it is not exposed to subsequent processes. Photosensitive inks, carbon ink, and silver ink are common; carbon and silver inks are conductive. Typical ink colors include white, green, black, blue, red, and yellow.
White ink is often used on FPCs for legend and symbols, such as diode markings. Black ink is applied over large areas of FPC circuitry to reinforce mechanical strength (and sometimes for confidentiality). Green ink provides insulation at solder joints and is typically used on FPCs where no protective film is present. The physical properties of ink—viscosity, thixotropy, and fineness—are critical to understand for effective use.
Key physical properties: viscosity and thixotropy
Screen printing is an essential step in PCB manufacturing. To achieve image fidelity, ink must have good viscosity and suitable thixotropy. Viscosity is the internal friction of a liquid—the resistance to sliding between layers. Thick liquids have higher mechanical resistance; thin liquids have lower resistance. Viscosity is measured in poise, and temperature has a marked effect on it.
Thixotropy is a physical property where viscosity decreases under agitation and quickly recovers when left to stand. Stirring can sustain this effect long enough to rebuild internal structure. For high-quality screen printing, thixotropy is crucial: as the squeegee moves, the ink is agitated and becomes more fluid, accelerating passage through the mesh and helping separate strands merge uniformly. When the squeegee stops, the ink returns to rest and viscosity recovers to the required value.
Fineness and other considerations
Pigments and mineral fillers are solid particles, typically ground to a size not exceeding 4/5 micron, and form a homogeneous flow. Fineness is therefore an important requirement for ink. In addition to viscosity and thixotropy, fineness affects print resolution and consistency.

Types of PCB inks
PCB inks fall into three main categories: circuit inks, solder mask inks, and legend inks.
- Circuit ink acts as a resist during etching, protecting the circuit. It is usually photoimageable liquid, available in acid-resistant and alkali-resistant versions (the alkali-resistant type is more expensive). After etching, the ink is removed with alkali.
- Solder mask ink is applied over the finished circuit for protection. It can be photoimageable liquid, thermal-cure, or UV-cure, and it remains on the board except over pads to facilitate soldering and provide insulation and oxidation resistance.
- Legend ink is used for markings on the board surface, such as component symbols, and is typically white.
Other inks include peelable ink, which protects areas during copper plating or surface finishing and is later removed, and silver paste ink.
Ink handling best practices
Based on practical experience, the following guidelines help maintain ink quality:
- Keep ink temperature below 20–25°C and avoid large fluctuations, which can affect viscosity and print quality. If ink has been stored outdoors or at varying temperatures, allow it to acclimatize for several days before use. Cold ink can cause screen printing defects.
- Before use, mix thoroughly by hand or machine. If air is entrapped, let it stand. For dilution, mix first, then check viscosity. Reseal the container immediately after use, and never return ink from the screen to the original container.
- Clean screens with a compatible cleaning agent, and use clean solvent for final rinsing.
- Dry ink in an enclosure with good exhaust ventilation.
- Ensure the working environment meets process requirements for screen printing.
What this means for your build
- Specify the right ink type for your application. For FPCs requiring flexibility and insulation, choose solder mask inks compatible with the flex material and cure method.
- Control storage and handling. Inks are sensitive to temperature and contamination; ensure your manufacturer follows strict storage and mixing procedures.
- Understand the role of conductive inks. If your design uses carbon or silver ink for conductivity, confirm their compatibility with the assembly process.
- Consider legend and mechanical reinforcement. White legend ink and black reinforcing ink can improve readability and durability.
- Communicate with your fabricator. Discuss ink selection early to avoid issues during prototyping and volume production.
Source: compiled from public web sources.